Williams Strength Products

Deluxe Line Specifications

Bar Catches

Regular

UHMW Covered

Bar catches manufactured with 3/8" flat bar. 1" round peg

inserts completely thru post. UHMW plastic protection is

available on high wear areas. A weld bead is added for

strength.

Advantages - 3/8" flat bar stronger than 1/4" used by some manufactures. 1" peg goes thru both

holes in post for strength. Can be used on both sides of post instead of having to purchase

special reverse catches. Catches can be adjusted in 3" increments.

Spotter Platforms

Integrated with bench and sloped to allow change in height from incline to military.

Advantages - Spotter platforms stays with bench and can be used when spotting dumbbell lifts.

Slopped height is better than fixed height. By not locking bench into rack the bench can be picked

up from the front and moved with ease. Benches that are picked up from the back are very difficult

to move as you most bend under the Olympic bar (very bad on the back) or remove it first.

Frame Components

All componets made in jigs and mig wire welded. Tubes are caped with welded steel end caps.

Advantages - Consistancy in construction from the use of jigs. Welded end caps much better

than plastic end caps.

Assembly

Bolt thru design with two 1/2" bolts per connection. 3/8" plates welded to tubing at most

attachment points.

Advantages - 3/8" plates add strength to tubing. Bolts will not get loose over time and 1/2"

lock nuts have much more thread area than 4 small bolts threaded into 3/16" steel tubing

as some manufactures use.

Finish

Powder coating is standard on all steel components. Multi-racks have black texture

powder coated post. Metal is pre-treated with phosphate wash and powder is baked on

in gas fired oven for 30 minutes at 400 degrees.

Advantages - Textured posts keep racks looking good longer than standard powder coating.

Other high wear ares are coated in black texture for longer lasting finish.

Frame Construction

3" x 3" x 11 gauge and 2" x 3" x 11 gauge tubing standard with 3/16" thickness available.

Most racks have raised base supports and "walk thru" design.

Advantages - Racks do not have to be 3/16" tubing because the corners are not cut out down

the length of the tube and no bolts are just taped into the tubing with no nuts attached. Raised

base supports allow for wide sumo squat stance if desired and walk thru design allows benches

to be rolled in and out either side.

Safety Spotter Bars

2" x 2" x 11 guage with quick adjust design. UHMW protection on top of spotter and UHMW

tape on inside available.

Advantages - No need for heavy 3/16" tubing as these safety bars have been tested and

withstand any abuse without bending. Other types of safety spotters are either extra heavy

or bend with light weights dropped on them. Round bar safety spotters must be pulled all the

way thru both post to adjust.

Weight Storage

1" solid round bar welded to 3/8" flat bar and bolted on. Round bar covered with 1 1/2"

UHMW protection available.

Advantages - 1" round welded to 3/8" flat is much stronger than round welded to thinner

tubing and round tubing welded to tubing. If a peg was ever bent a new unit can be bolted

on with ease. All of WSP designs allow for easy to get to plate heights. Even shorter users

can reach the highest plates.

Warranty

Lifetime frame warranty, 2 Years moving parts and 90 days upholstry.

Chin Up Bar

Standard bars are 1 1/4" solid round bar. Options include 1 1/4" cambered bar with two

parallel rubber covered grips, 2" knurled fat bar and swivel handle bar with stainless steel

slide.

Advantages - Any combination of bars can be added to any rack.

0-90 Benches

2" x 3" x 11 guage contruction. No pop-pin design.

Advantages - Small gap between pads. No pop-pin design has no parts that can get

lose and lost over time. Very easy to adjust incline. Picked up and moved from the

front.

Custom Logos

Advantages - Custom laser logos, platform logos and high wear logos add

an extra touch to give a truly distinctive look to each order. Full color high

wear logos on plastic vinyl does not soak up hair oils like normal vinyl.

Platforms

2" x 2" x 11 guage frames. Construction consists of 2 and 3 layers of wood and rubber.

Total thickness is 1 1/2". Rubber area is 2 layers of 3/4" rubber. Wood area is real oak

hardwood flooring built up to 1 1/2".

Advantages - Multi-layer design is and feels extremly solid and protects the room's base

floor. When attached to racks a ramp is included to allow for benches to be rolled on and

off with ease.

Feet

Racks and benches have welded steel feet to keep equipment stationary. No plastic end

caps to lose.

Insurance

$2,000,000 Products and completed liability policy backs all equipment.